Honda Accord: Front Door Glass and Regulator Replacement - Doors - Body - Honda Accord MK8 2008-2012 Service ManualHonda Accord: Front Door Glass and Regulator Replacement

Eighth generation (2008–2012) / Honda Accord MK8 2008-2012 Service Manual / Body / Doors / Front Door Glass and Regulator Replacement

NOTE: Put on gloves to protect your hands.

1. Remove the door panel: - 2-door (see page 20-12) - 4-door {see page 20-17) 2.2-door: Remove the screws, then remove the door panel bracket (A).

3. Disconnect the power door lock actuator connector


3. Disconnect the power door lock actuator connector (A), and detach the harness clips (B). Remove the plug caps (C). 4-door: Disconnect the power mirror connector (D).

2-door

4-door


4-door

4. Pass the wire harness (E) through the slit (F) in the


4. Pass the wire harness (E) through the slit (F) in the plastic cover (G), then remove the plastic cover.

NOTE: If the plastic cover is damaged or torn, replace it with a new one.

5.4-door: Remove the bolts, and release the hook (A), then remove the door panel bracket (B).

6. Lower the glass (A) until you can see the bolts, then


6. Lower the glass (A) until you can see the bolts, then remove them. Carefully pull the glass out through the window slot. Take care not to drop the glass inside the door.

2-door

4-door


4-door

7. Disconnect the connector (A) from t h e regulator ( B ) .


7. Disconnect the connector (A) from t h e regulator ( B ) .

2-door

4-door


4-door

8. Remove the bolts (C), and loosen t h e bolts (D).


8. Remove the bolts (C), and loosen t h e bolts (D).

Release the h o o k (E), then remove t h e regulator through the hole in the door.

9. Apply multipurpose grease to all the sliding surfaces of the regulator (A) where shown. 4-door is shown; 2-door is similar.

10. Install the glass and the regulator in the reverse order


10. Install the glass and the regulator in the reverse order of removal, and note these items: - If the clips are damaged or stress-whitened, replace them with new ones.

- Roll the glass up and down to make sure it moves freely without binding.

- Make sure that there is no clearance between the glass and the glass run channel when the glass is closed.

- Make sure the connector is plugged in properly.

- Adjust the position of the glass as necessary, (see page 20-56) - Do the power window control unit reset procedure (see page 22-280).

- Make sure the plastic cover on the door is installed properly and sealed around its outside perimeter to seal out water.

- Push the clips and the hooks into place securely.

- Check for water leaks, (see step 9 on page 20-57) - Make sure the power door locks, the windows and the power mirror operate properly.

- Test-drive the vehicle, and check for wind noise and rattles.

    Front Door Latch Replacement
    NOTE: Put on gloves to protect your hands. 1. Remove the door panel and the inner handle: - 2-door ( s e e p a g e 20-12) - 4-door (see page 20-17) 2. Remove the plastic cover, as needed (see st ...

    Front Door Sash Inner Trim Replacement
    2-door NOTE: Take care not to scratch the door. 1. Remove the door panel (see page 20-12). 2. Lower the glass fully. 3. Remove the door sash inner trim (A). -1. Detach the clip fastening ...

    See also:

    Starter Removal and Installation
    Removal 1 Do the battery removal procedure (see page 22-92). 2. Remove the intake manifold (see page 9-4). 3. Disconnect the positive starter cable (A) from the B terminal, and the S terminal ...

    Rear Seat Access Cable Replacement
    2-door Passenger's Seat NOTE: - Put on gloves to protect your hands. - Take care not to kink the rear seat access cable. - The right rear seat access cable is shown; the left rear seat access ...

    ATF Feed Pipe Replacement
    1. Remove the snap rings (A), the ATF feed pipes (B), and the feed pipe flanges (C) from the end cover (D). NOTE: Replace the end cover, if the 1st clutch ATF feed pipe (E) replacement is require ...